200pcs Black Allen Head Socket Internal Hex Set Grub Screw Assortment Cup Point Screws Kit for Home Use
400PCS Insulated Cord Pin End Terminals Wire Copper Crimp Connector AWG22-10 Electrical Wire Connector Set
1450PCS 2.54mm PCB Jumper Wire Pin Header Connector Female Male 40Pin Box Packaging Kit Electronic Components Set for Arduino Dupont
560PCS Wire Jumper Connector Cable Pin Header Housing Male / Female Pins Head Terminal Adapter Plug Set for Dupont
200PCS M5-M14 Copper Washers Gasket Set Flat Ring Seal Assortment Kit with Box 9 Sizes for Hardware Accessories
200pcs Stainless Steel Socket Screws Allen Head Socket Hex Set Grub Screw Assortment Cup Point Column M3-M6/M8 Hexagonal Screw Kit
The ZVS low voltage induction heating board module adopted super PCB layout design and super heat sink,heat dissipation good,since with a cooling fan interface,can also do Tesla discharge,generator voltage inverter,etc..
The ZVS induction heater can be used by DIY players to give smaller players the parts can be treated by quenching,annealing and other heat treatment.
You can also be melted with graphite crucible Kim,silver,copper,aluminum and other metal,heating evenly,is fast and very convenient.
This zvs flyback driver product is available at under the condition of good heat dissipation,the utility model can work continuously for hours.
This module has specific voltage and current requirements,the voltage 12V current must be more than 10A power supply can be used,if the power is too low will lead to the power output is greatly reduced,when the voltage is lower than 12V,it will lead to two MOS at the same time conduction,will burn MOS tube.
Max Power : 1800W
Max current: 40A
Input voltage: 12V-48V
Recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
Package Size: 30*13.5*11.5cm / 12*5*4.5in
Package Weight: 1162g / 41oz
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does not inclues)
4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
6. The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
8. Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous
10. Induction heating power is great, so fever is normal, be sure to do a good job of cooling.
11. Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
1 * Induction Heating Board
1 * 48V Copper Tube